|
GEAR-PITCH
TYPE AUTO TAPPING MACHINE
|
FEATURE |
| * |
Gear type |
| |
Equipped with
replaceable AB gears and meet the tap of process thread with the pitch,
the comparison between gear type and leading screw type is as follows: |
| |
| 1.
|
Fine thread
will be to limited tapping. |
| 2.
|
Not easy
to replace |
| 3.
|
Unable
to high speed running, tapping capacity will be to limited.
|
| 4. |
Leading
screw type is easy to wear and tear promptly due to long-term
wear that could cause quality problems, such as bad tapping
jobs . etc. |
|
| * |
Gear pitch
auto tapping machine |
| |
It is designed
to have one pitch by per turn, to feed and return back the knife synchronously
and mechanically. Therefore, it is even though the soft plastic work
piece, that could be tapped perfectly. It can make use of selecting
push button or pedal switch to operate single up and down stroke,
or use knob to operate round stroke. |
| * |
Convenience
to operate |
| |
| 1. |
The work
piece won't jump & pull-up when tapping due to one pitch
by one turn. Just only to prevent work piece being rotated,
it will simplified fixture, it is not necessary to hold down
or clamp |
| 2. |
Equipped
particularly with 2 clutches that make the main shaft return
automatically to protect the tap while is tapping but not in
alignment with hole or torsion exceeded. |
| 3. |
Even if
operated by a beginner or a novice of the end of users, the
quality and efficiency will not be affected. |
| 4. |
Easy to
adjust the tapping stroke on the index disk. |
| 5. |
Available
for all modes to equip with extra multi-spindle device to make
it efficiently. |
|
|
JT-4508
|
| GEAR-PITCH
TYPE AUTO TAPPING MACHINE |
|
FEATURE |
| * |
Installed
an isolated cooling fan in the interior of motor to dissipate
dissipate heat. Could be operated continuously, steady and durable. |
| * |
Vertical
column is solid and treated by tempering to get rid of stress,
surface is chrome plated, wear resisting and no rust. |
| * |
High
speed rotation continuously, 42 times/per Minute. |
|
 |
| Vertical
type JT-4508
Weight(about
120kg) |
Main
spindle
max. stroke
(mm) |
Type
of the
front side of
Main spindle
(mm) |
Diameter
of
thread (mm) |
Up
and Down moving
distance of the head
(mm) |
Distance
between
the main spindle
and the table
(mm) |
Working
table
size(mm) |
| 45 |
JT-2
CT-12 |
 2~8
Less than(10) |
260 |
350 |
225X230 |
| Motor |
Main
spindle speed
(R.P.M.) |
Auto
feeding thread
pitch for which
suits machine |
Max.
capacity of
Multi-spindle |
Packing
dimension
(cm) |
G.Weight
(kg) |
| 50HZ |
60HZ |
Range
of TPI |
mm |
m/m
m/m standard
thread pitch |
3PH
4P
0.37KW
(1/2HP) |
1340
760
420 |
1600
900
500 |
64,56,48,
44,40,32,
28,24,20,
18,16 |
0.2,0.25,0.3
0.35,0.4,0.45
0.5,0.6,0.7
0.75,0.8,0.9
1.0,1.25
(1.5) (1.75)
|
3X10
spindles
4X5 spindles
5X2 spindles |
73
X 52 X 82
(L)X(W)X(H) |
145 |
|
|
